MTD 737-0168 Manual do Operador

Operator's ManualTwo StageSnow Thrower33" Model ShownIMPORTANT: Read safety rules and instructions carefully before operating equipment.Warn

SECTION4: OPERATINGYOURSNOWTHROWERBeforeStartingRead and understand all instructions and warnings onthe machine and in this manual before operating.Ga

loud clattering sound, which is not harmful to theengine or starter.Move throttle control to "stop" or "off" position.Remove ignit

SECTION5: MAKINGADJUSTMENTS_ ARNING" NEVER attempt to clean chuteor make any adjustments while engine isrunning.ShiftRod• Remove the hairpin clip

SkidShoeThe space between the shave plate and the ground canbe adjusted by raising or lowering the skid shoes.For close snow removal, as when using on

Shear Pin_/ Cotter PinVent PlugFigure 16DischargeChuteThe base of the discharge chute and the spirals on thechute crank should be lubricated at least

SECTION7: SERVICINGYOURSNOWTHROWER_ ARNING" Before servicing, repairing, orinspecting, disengage all clutch levers and stopengine. Wait until all

Engine PulleyShoulder Boltand WasherERe"PulleyAuger IdlerBrakeAssemblyZ FittincFigure 20_3_-_Auger ControlBeltCable RollerDrive Belt• Unhook the

ChangingFrictionWheelRubberThe rubber on the friction wheel is subject to wear andshould be checked after the first 25 hours of operation,and periodic

SECTION8: 0FF-SEASONSTORAGE_ ARNING" Never store engine with fuel intank indoors or in poorly ventilated areas,where fuel fumes may reach an open

MANUFACTURER'S LIMITED WARRANTY FOR:YaRD.MaNTM®Thelimited warranty setforth below is given by MTD LLC withrespectto new merchandise purchasedand

ContentCustomerSupportImportantSafeOperationPracticesAssemblyKnowingYourSnowThrowerOperatiingYourSnowThrowerTABLEOFCONTENTSPage Content Page2 Ajustmen

Forinformationonlightsandhandlepanelsrefertopages30and31./Voir /es pages 30 et 31 pour toutrenseignement concernant le tableau debord et les phares.63

REFNO.N° DEREF12345677891011121314151618192122232425262728293031323334353637384o414244464748495051525354565758616263777879808182838487899o919293949899

82125460 176763 70387378 728159632632Shave plate shouldride slightly aboveashpalt. Set toTorque to 20-30 in./Ibs./Serrez a un couple de 20-30 po-/b.56

REFNO.N° DEREF1235789101112131415161718192021222324262728293031323334384345464852535456585960616365676869707172737476777879PARTNO.N° DEPII_CE736-01597

REFNO. NO.N° DE N° DERI_F PII_CE80 618-0247618-043581 710-1260A82 712-042983 714-013584 750-0402085 741-019287 738-0415590 05845C784-0315A91 741-01929

15107\1361617\Torque to 21 ft./Ibs, max-imum, cupped washershould be flat./Serrez a un couple de 21 ...-_pHb maximum. La18201914REFNO.N° DEREF1234

16977864351492985 1772//23z65025597386 14 85 43 3183 _--_s _j81_ _, o4_828O26

REFNO.N° DERI_F1234a4b4c56789101112131415161718192021222324252627293031323334353637383940414243444546474849505152535455565758A58B58PARTNO.N° DEPIECE61

REFNO.N°DEREF5960616263646566676869707172737475767778798O81828384858687PARTNO.N° DEPIECE741-04025741-0225741-0563741-04076741-0748746-0949A746-0951747

4I!29_23 18Engine is for reference onlyand may not resemble the en-gine on your snowthrower. /Le moteur est represente a ti-tre indicatif seu/ement et

SECTION1: IMPORTANTSAFEOPERATIONPRACTICESWARNING: This symbol points out important safety instructions which, if not followed, could endanger theperso

8STYLE 6Chute tilt cut-out/Ouvertures pour goulotte incfinable.IHole for mounting heated grip toggleswitch./Trou de montage ducommutateur a culbuteur

REFNO.N° DEREF.456789101213151617181920212223252627283132333436383940PARTNO.N° DEPll_CESTYLE3731-1737A731-0061731-1873A731-2564731-2606STYLE 6731-2516

6. Donotoperatemachinewhileundertheinfluenceofalcoholordrugs.7. Mufflerandenginebecomehotandcancauseaburn.Donottouch.8. Exerciseextremecautionwhenoper

SECTION2: ASSEMBLINGYOURSNOWTHROWERNOTE: This Operator's Manual covers several models.Snow thrower features vary by model. Not allfeatures discus

AttachingtheChuteAssemblyNOTE: Your chute assembly may or may not beassembled. If # requires assembly use the followinginstructions.j Chute AssemblyHe

ChuteClean-OutToolThe chute clean-out tool is conveniently fastened tothe rear of the auger housing with a mounting clip.Use the clean-out tool to cle

CouplerSpringCable\ \ \Lock NutFigure 10Tire Pressure (PneumaticTires)The tires are overinflated for shipping purposes.• Check tire pressure. Maintain

AugerControlThe auger control is located on theleft handle. Squeeze the augercontrol to engage the augers.Release to stop the snow throwingaction. The