MTD 600 SERIES Manual do Operador

Safe Operation Practices • Set-Up • Operation • Maintenance • Service • Troubleshooting • WarrantyLTwo-Stage Snow Thrower m 500 Series & 600 Serie

Push the hex rod toward the control panel until the holein the hex rod lines up with the hole in the chute controlinput closest to the chute control h

2_Place chute assembly onto chute base and secure chutecontrol assembly to chute support bracket with clevis pinand cotter pin removed earlier. See Fi

Set-UpShearPinsStorage(if s0equipped)A pair of replacement auger shear pins and bow tie cotter pinsare included with your snow thrower. If your snow t

AdjustmentsChuteAssemblyNOTE: Chutes on models with 4-Way Chute Control are alsocontrolled by the Chute Directional Control. See Fig. 4-1.The distance

AugerControlWARNING! Prior to operating your snow thrower,carefully read and follow all instructions below.Perform all adjustments to verify your snow

ControlsandFeatures4fShift LeverChute Directional Control_e=====Auger Control\Heated GripsSteeringTriggerDrift Cutter/DriveShift Leverer ControlOverhe

Drift Cutters (ifsoequipped)The drift cutters are designed for use in deep snow. Their useis optional for normal snow conditions. Maneuver the snowthr

2-WayChute Directional Control (ifsoequipped)CHUTE DiRECTiONAL CONTROLCHUTEROTATE CHUTEROTATELEFT RIGHTADJUSTABLECHUTETiLTThe chute directional contro

OperationStarting and Stopping the EngineRefer to the Engine Operator's Manual packed with your snowthrower for instructions on starting and stop

Maintenance&Adjustments6MaintenanceEngineRefer to the Engine Operator's Manual packed with your snowthrower.TirePressureRefer to page 12 for

ToTheOwner1ThankYouThank you for purchasing an MTD Snow Thrower. It was carefullyengineered to provide excellent performance when properlyoperated and

AugerShaftAt least once a season, remove the shear pins from the augershaft. Spray lubricant inside the shaft and around the spacers andthe flange bea

ChuteControl Rod(2-Way& 4-WayChuteControl)To adjust the chute control rod, proceed as follows:I. Remove the cotter pin from the hole closest to th

Service7Belt ReplacementAuger BeltTo remove and replace your snow thrower's auger belt, proceedas follows:I. Allow the engine to run until it is

7. Drive BeltRemove the belt from around the auger pulley, and slip thebelt between the support bracket and the auger pulley.See Fig. 7-5.Figure 7-58.

6.Back out the stop bolt to increase the clearance betweenthe friction wheel disc and friction wheel. See Fig. 7-7.//Figure 7-77. Slip the drive belt

5.Carefully remove the hex nut which secures the hex shaftto the snow thrower frame and lightly tap the shaft's end todislodge the ball bearing f

TroubleshootingProblem CauseRemedyEngine running erratically/inconsistent RPM (hunting orsurging)Excessive vibrationUnit fails to propel itselfEngine

ReplacementParts9Component Part Number and Description929-0071A954-04050954-04260954-04195954-04201A684-04159684-04153935-04054725-1629925-1658738-041

Attachments&Accessories1The following attachments and accessories are available for your snow thrower. Phone (800) 800-7310 for information regard

1129

ImportantSafeOperationPractices2WARNING! This symbol points out important safety instructions which, if not followed,could endanger the personal safet

SECTION11 -- NOTES

SECTION11 -- NOTES 31

MANUFACTURER'S LiMiTED WARRANTY FORThe limited warranty set forth below is given by MTD LLCwithrespect to new merchandise purchased andused in th

SafeHandling of GasolineTo avoid personal injury or property damage use extreme carein handling gasoline. Gasoline is extremely flammable and thevapor

Clearinga CloggedDischargeChuteHand contact with the rotating impeller inside the dischargechute is the most common cause of injury associated with sn

Safety SymbolsThis page depicts and describes safety symbols that may appear on this product. Read, understand, and follow all instructions on themach

Assembly& Set-Up3Contentsof CartonOne Snow ThrowerHex Rod (if so equipped)Chute Control Rod (if so equipped)Two Replacement Auger Shear PinsOne Sn

2-Way& 4-WayAssemblyRemove all loose parts before assembling.HandleAssembly1. Place the shift lever in the Forward-6 position2. Observe the lower

3.4.Place chute onto chute base and ensure hex rod ispositioned under the handle panel. Install hex boltpreviously removed but do not secure with wing