Mtd 465 Manual do Utilizador descarregar pdf (Página 6)

Anaching The Hopper Assembly (aii Models)

* Remove six hex nuts and washers from the weld

studs on the impeller housing. Leave the support

plate in place on the weld studs. See Figure 2.

• Place hopper assembly into position in front of

impeller housing, aligning holes in hopper

assembly collar with weld studs.

• Slide hopper assembly onto weld studs and replace

washers and hex nuts. Do not tighten completely.

• Lift hopper assembly up to impeller bracket

assembly and slide the release rod out slightly to

hook the hopper bracket onto the rod. See Figure 2.

• Tighten the six hex nuts that secure hopper

assembly to impeller housing and also tighten the

hex nuts that secure hopper bracket to hopper

assembly.

Attaching The Discharge Chute (ah Models)

• Remove the wing knobs from each side of the lower

impeller housing. See Figure 3.

Remove the hex lock nut, spacers, and hex bolt

from the top of the impeller housing.

Align the discharge chute in position on the

discharge opening and insert hex bolt with spacer

through hinge on discharge chute (spacers fit inside

of hinges). See Figure 3.

Place second spacer over hex bolt inside other

hinge and secure with hex lock nut.

• Secure both sides of discharge chute to impeller

housing using wing knobs previously removed.

Attaching The Chipper Chute

(Model 463 Thru 465 Only)

• Remove the three cupped washers and hex nuts

from weld studs besides the opening on the side of

the impeller housing. See Figure 4.

• Remove the hex bolts, lock nuts, and flat washers

from the two holes on the upper end of the support

brace.

Align the chipper chute over the weld studs, so the

slot in the bottom of the chute is facing down.

Secure chipper chute with the three cupped

washers (cupped side against the chipper chute)

and hex nuts previously removed. Do not tighten

the nuts at this time.

The chipper shredder was shipped with one end of

the support brace already secured to the lower

frame. Loosen but do not remove the bolts securing

the brace to the frame.

Align the holes in the chute with the holes in the top

of the brace and attach brace to chipper chute with

hardware previously removed. Tighten securely.

Tighten the bolts securing the support brace to the

frame.

Tighten the three nuts on the weld studs holding the

chipper chute to the impeller housing.

Attaching The Bag (am Models)

To attach the bag, place the opening of the bag

completely over the discharge chute.

Depress the plunger on the drawstring and pull on

the drawstring until the bag is tight around chute

opening. Release plunger to lock it into position.

1 2 3 4 5 6 7 8 9 10 11 12 13 14

Comentários a estes Manuais

Sem comentários

Sharp XG-SV200X Arkusz Danych (4 strony)

Marka: Sharp | Kategoria: Data projectors | Rozmiar: 6.25 MB |

Spis treści

Ceiling Swivel Mount Option

Flexible Installation

3D Ready with DLP

Link™ Technology

Reliable Performance

Więcej produktów i instrukcji dla Projektory danych Sharp

Modele	Rodzaj dokumentu
PGD50X3D	Arkusz Danych Sharp PGD50X3D data projector, 2 strony
XG-P560WN	Arkusz Danych Sharp XG-P560WN data projector, 2 strony
XG-C465X-L	Arkusz Danych Sharp XG-C465X-L data projector, 2 strony
PG-D2500X	Arkusz Danych Sharp PGD2500X data projector, 2 strony
PG-F267X	Arkusz Danych Sharp PG-F267X data projector, 2 strony
ANPH823EZ	Arkusz Danych Sharp XG-PH80WN data projector, 4 strony
PG-D4010X	Arkusz Danych Sharp PG-D4010X data projector, 2 strony
XG-F262X	Arkusz Danych Sharp XG-F262X data projector, 2 strony
XG-C335X	Arkusz Danych Sharp XG-C335X data projector, 2 strony
XV-Z12000E	Arkusz Danych Sharp XV-Z12000, 1 strony
XR-1R	Arkusz Danych Sharp XR-1R data projector, 1 strony
XR-10X	Arkusz Danych Sharp DLP Multimedia Projector XR-10X, 4 strony
XG-C55X	Arkusz Danych Sharp Desktop LCD XGA 1024x768 3000 ansi lumen 400:1, 1 strony
XV-Z10E	Arkusz Danych Sharp XV-Z10E data projector, 1 strony
PG-C20XE-BU	Arkusz Danych Sharp PG-C20XE data projector, 1 strony
XG-P25XE	Arkusz Danych Sharp Desktop LCD XGA 1024x768, 1 strony
XG-C50XE	Arkusz Danych Sharp XG-C50X, 1 strony
PG-A10S	Arkusz Danych Sharp Notevision PG-A10S Projector, 2 strony
PG-A20X	Arkusz Danych Sharp Ultra portable LCD XGA 1024x768 2000 ansi lumen, 2 strony
XG-C68X	Arkusz Danych Sharp DLP data video projector, 106 strony

Mtd 465 Manual do Utilizador Página 6

Comentários a estes Manuais

Sharp XG-SV200X podręczniki

Sharp XG-SV200X Arkusz Danych (4 strony)

Spis treści

Więcej produktów i instrukcji dla Projektory danych Sharp